Rigol DSG3000 Series Spezifikationen

RIGOL User’Guide DS6000 Series Digital Oscilloscope May 2011 RIGOL Technologies, Inc.

RIGOL DS6000 User’s Guide VIII Pollution Degree Degree 2 Pollution Degree Definitions Pollution degree 1: No pollution or only dry, non-condu

RIGOL DS6000 User’s Guide 5-10 Pulse Trigger Trigger on positive or negative pulse with specified width. Trigger Type: Press Type to select

RIGOL DS6000 User’s Guide 5-11  When the Pulse Condition is set to , , or , press Set Up and use to input the desired value.

RIGOL DS6000 User’s Guide 5-12 Slope Trigger Trigger on the positive or negative slope with specified time. Trigger Type: Press Type to sele

RIGOL DS6000 User’s Guide 5-13  When the Slope Condition is set to , , or , press Time and use to input the desired value. T

RIGOL DS6000 User’s Guide 5-14 unchanged.  : adjust the upper and lower limits of the trigger level at the same time. During the adjustmen

RIGOL DS6000 User’s Guide 5-15 Video Trigger Trigger on the standard video signal fields and lines of NTSC (National Television Standards Committee

RIGOL DS6000 User’s Guide 5-16  SECAM: the frame frequency is 25 frames per second. The sweep line is 625 with interlacing sweep. Trigger M

RIGOL DS6000 User’s Guide 5-17 Pattern Trigger Identify the trigger condition through searching for the specified pattern. Pattern is the logic “AND”

RIGOL DS6000 User’s Guide 5-18 define another edge item, thus the former edge item defined will be replaced by X. Trigger Mode: Press S

RIGOL DS6000 User’s Guide 5-19 RS232 Trigger Trigger according to the start frame, error frame, check error and data. Trigger Type: Press Type to

RIGOL DS6000 User’s Guide IX General Care and Cleaning General Care Do not leave the instrument exposed to direct sunlight for long period of time.

RIGOL DS6000 User’s Guide 5-20 19200 bps, 38400 bps, 57600 bps, 115200 bps and user-defined. After “User” is selected, press the Setup

RIGOL DS6000 User’s Guide 5-21 I2C Trigger Trigger on the start condition, restart, stop and missing acknowledgement or on the read/write frame wit

RIGOL DS6000 User’s Guide 5-22 --Press the ByteLength softkey to set the length of data and the range is from 1 to 5; --Press the CurrentBi

RIGOL DS6000 User’s Guide 5-23 SPI Trigger Trigger on the data pattern with specified edge. When using SPI trigger, you need to specify the SCL, SD

RIGOL DS6000 User’s Guide 5-24 Press ClockEdge to select the desired clock edge.  : trigger on the rising edge of the data pattern when the

RIGOL DS6000 User’s Guide 5-25 CAN Trigger Trigger on the specified frame type of the data frame. When using CAN trigger, you need to specify th

RIGOL DS6000 User’s Guide 5-26 format). -- Press the Bits softkey and use to set the desired value. The range is from 1 to 8. -- Press the

RIGOL DS6000 User’s Guide 5-27 Press SamplePoint and use to modify the parameter with the step as 1% and the range is from 5% to 95%. Trigger Mode

RIGOL DS6000 User’s Guide 5-28 USB Trigger Trigger on the SOP, EOP, RC, Suspended and Exit Suspended of the data packet on the differential

RIGOL DS6000 User’s Guide 5-29 Trigger Level: Use TRIGGER LEVEL to modify the level. For details, please refer to the description of “Tr

RIGOL DS6000 User’s Guide X Environmental Considerations The following symbol indicates that this product complies with the requirements of E

RIGOL DS6000 User’s Guide 5-30 Trigger Ouput Connector The trigger output connector at the rear panel can output trigger signals decided by t

RIGOL DS6000 User’s Guide 6-1 6 To Make Measurements After data is sampled and displayed, the DS6000 can make math operation, cursor measurement

RIGOL DS6000 User’s Guide 6-2 Math Operation DS6000 can realize various math operations of waveforms between channels including: add

RIGOL DS6000 User’s Guide 6-3 Subtraction Subtract the waveform voltage values of signal source B from A point by point and display the results. Pre

RIGOL DS6000 User’s Guide 6-4 Division Divide the waveform voltage values of signal source A by B point by point and display the results. It

RIGOL DS6000 User’s Guide 6-5 FFT FFT is used to quickly perform Fourier transform on specified signals and transform time domain signals to frequenc

RIGOL DS6000 User’s Guide 6-6 2. Select Window Function Spectrum leakage can be considerably decreased when a window function is used. DS

RIGOL DS6000 User’s Guide 6-7 Full Screen: the source channel and the FFT operation results are displayed in the same window to view the frequency spe

RIGOL DS6000 User’s Guide 6-8 Logic Operation Perform logic operation on the waveform voltage values of the specified source point by point a

RIGOL DS6000 User’s Guide 6-9 Press MATH  Operate to select “Logic”:  Press Expression to select the desired operation expression and the default

RIGOL DS6000 User’s Guide XI DS6000 Series Overview Being a multifunctional and high performance digital oscilloscope, DS6000 delivers perfect combin

RIGOL DS6000 User’s Guide 6-10 Advanced Operation DS6000 provides advanced operation function that allows user-defined operation func

RIGOL DS6000 User’s Guide 6-11 1. Expression Here, it refers to the formulas formed by channel, function, variable, operator and figure. The length o

RIGOL DS6000 User’s Guide 6-12 variable. After setting the “Step” or pressing this softkey, turn the knob to modify this parameter. The range

RIGOL DS6000 User’s Guide 6-13 Auto Measurement DS6000 provide auto measurements of 22 waveform parameters and the statistic and analytical functions

RIGOL DS6000 User’s Guide 6-14 Quick Measurement after Auto When the oscilloscope is correctly connected and has detected input signal, press

RIGOL DS6000 User’s Guide 6-15 One-key Measurement of 22 Parameters Press the MENU key at the left of the screen to turn on the measurement menu of t

RIGOL DS6000 User’s Guide 6-16 Time Parameters 1. Period: defined as the time between the two crossing points of th

RIGOL DS6000 User’s Guide 6-17 Delay and Phase DelaySource ASource BPeriod 1. Delay A→B : the time deviation between the rising edges of sourc

RIGOL DS6000 User’s Guide 6-18 Voltage Parameters 1. Vmax: the voltage value from the highest point of the

RIGOL DS6000 User’s Guide 6-19 9. Overshoot: the ratio of the difference of the maximum value and top value of the waveform to the amplitude value. 1

RIGOL DS6000 User’s Guide XII  Provide more than 2-hour lithium battery power supply (optional) to facilitate on-field test and use.  Buil

RIGOL DS6000 User’s Guide 6-20 Frequency Counter Measurement The hardware frequency counter supplied with this oscilloscope can make

RIGOL DS6000 User’s Guide 6-21 Measurement Setting 1. Source Selection Press MEAS  Source to select the desired channel for measurement (

RIGOL DS6000 User’s Guide 6-22 Press MEAS  Meas Setting  Type  “Phase” and then press Source A and Source B to set the two channel

RIGOL DS6000 User’s Guide 6-23 Clear the Measurement If you have currently turned on one or more items in the 22 measurement parameters,

RIGOL DS6000 User’s Guide 6-24 All Measurement All measurement could measure all the time and voltage parameters (totally 18) of the current

RIGOL DS6000 User’s Guide 6-25 Statistic Function Make statistic and display the current, average, minimum (or standard deviation) and maximum (or co

RIGOL DS6000 User’s Guide 6-26 Measurement History To view the history measurement data, press MEAS MeasHistory  MeasHistory  “On

RIGOL DS6000 User’s Guide 6-27 Cursor Measurement Cursors are the horizontal and vertical marks that can be used to measure the X axis values (usuall

RIGOL DS6000 User’s Guide 6-28 Manual Mode In this mode, a pair of cursors will appear. You can adjust the cursors to measurement the X (or Y

RIGOL DS6000 User’s Guide 6-29 3. Select X (Y) Axis Unit When the cursor type is “Time”, press Time Unit to select “s”, “Hz”, “°” or “%”.  S: when

RIGOL DS6000 User’s Guide XIII Document Overview 1 Quick Start Describes the preparations before using the instrument and generally introduce the ins

RIGOL DS6000 User’s Guide 6-30 5. Measurement Example Use manual cursor measurement to measure the period (△X) of a square wavefor

RIGOL DS6000 User’s Guide 6-31 Track Mode In this mode, one or two pairs of cursors will appear. You can adjust the two pairs of cursors to measure t

RIGOL DS6000 User’s Guide 6-32 operation results (MATH) as the measurement source of cursor B (only channels that are turned on are available)

RIGOL DS6000 User’s Guide 6-33 Cursor Track (Before Horizontal Expansion): Cursor Track (After Horizontal Expansion):

RIGOL DS6000 User’s Guide 6-34 Auto Mode In this mode, one or more cursors will appear. You can use auto cursor measurement to measure anyone

RIGOL DS6000 User’s Guide 7-1 7 Protocol Decoding Protocol analysis can be used by users to discover errors, debug hardware and accel

RIGOL DS6000 User’s Guide 7-2 Parallel Decoding Parallel bus consists of clock line and data line. As shown in the figure below, CLK is the c

RIGOL DS6000 User’s Guide 7-3 Next, press Channel to specify a channel source for the bit currently selected in ChanBits. 3. Analog Chann

RIGOL DS6000 User’s Guide 7-4 RS232 Decoding (Option) RS232 serial bus consists of the transmitting data line (TX) and the receiving data lin

RIGOL DS6000 User’s Guide 7-5 Stop BitCheck BitStart PhaseData Bits Start Bit: represent when the data starts outputting. Setting the Polari

RIGOL DS6000 User’s Guide XIV oscilloscope. 13 System Function Setting Introduces how to perform the remote interface, system-related and p

RIGOL DS6000 User’s Guide 7-6 5. Data Packet Setting As mentioned before, in RS232, you need to set the start bit, the data bits, the check b

RIGOL DS6000 User’s Guide 7-7 Check Error: When check errors are detected during the decoding, the data will be filled with red batches. For example:

RIGOL DS6000 User’s Guide 7-8 SPI Decoding (Option) SPI serial bus consists of chip select line (SS), clock line (SCLK), MISO and MOSI. Host

RIGOL DS6000 User’s Guide 7-9 Press SCLK to turn on the clock line setting interface.  Press Channel to select any channel (CH1-CH4) as the clock ch

RIGOL DS6000 User’s Guide 7-10 with red patches. For example, when Data Bits is set to 8, and SCLK slope is set to rising edge, deording error

RIGOL DS6000 User’s Guide 7-11 I2C Decoding (Option) I2C serial bus consists of the clock line (SCLK) and the data line (SDA). HostDeviceSCLKSDAA2A1

RIGOL DS6000 User’s Guide 7-12 Press Offset and use to adjust the vertical display position of the bus. Press BusStatus to turn the bus dis

RIGOL DS6000 User’s Guide 7-13 CAN Decoding (Option) Press MATH  BUS1  Decode and select “CAN” to open the CAN decoding function men

RIGOL DS6000 User’s Guide 7-14 5. Threshold Refer to the introduction in Parallel Decoding. 6. Display-related Setting Press the Ary s

RIGOL DS6000 User’s Guide 8-1 8 Reference Waveform In actual testing process, the waveform being tested can be compared with the refe

RIGOL DS6000 User’s Guide XV Contents Guaranty and Declaration ... I Safety Req

RIGOL DS6000 User’s Guide 8-2 To Enable REF Function Press the REF function key in the vertical control area (VERTICAL) at the front panel to

RIGOL DS6000 User’s Guide 8-3 To Select REF Source Press Current and use to select any reference channel (Ref1-Ref10) that has been turned on and

RIGOL DS6000 User’s Guide 8-4 To Export to Internal or External Memory Users can also save the reference waveform to the Flash memory inside

RIGOL DS6000 User’s Guide 9-1 9 Pass/Fail Test Monitor the change of the signal by judging whether the input signal is within the creation mask.

RIGOL DS6000 User’s Guide 9-2 To Enable Pass/Fail Test Function Press UTIL  Pass/Fail to turn on the Pass/Fail test menu. Note that when the

RIGOL DS6000 User’s Guide 9-3 To Select Source Press Source to select the channel (CH1-CH4) to be tested. During the test, the oscilloscope will judg

RIGOL DS6000 User’s Guide 9-4 are detected. The test results on the screen will update continuously and the [Trig Out/Calibration] connector a

RIGOL DS6000 User’s Guide 10-1 10 Waveform Recording Waveform recording can record the waveforms in the input channels (CH1-CH4). Wavefor

RIGOL DS6000 User’s Guide 10-2 Waveform Recording Waveforms from all the channels currently turned on will be recorded during wave

RIGOL DS6000 User’s Guide 10-3 4. Maximum End Frame The menu shows the maximum end frame that can be recorded currently. As the capacity of the wavef

RIGOL DS6000 User’s Guide XVI Knob ... 1-20 Navigatio

RIGOL DS6000 User’s Guide 10-4 Waveform Playback Waveform playback can play back the waveforms currently recorded. Press UTIL  Record  Mode

RIGOL DS6000 User’s Guide 10-5 5. End Frame Press this softkey and use to set the end frame of the playback. The default is the number of frames o

RIGOL DS6000 User’s Guide 10-6 Waveform Analysis This function is used to analyze the recorded waveform. Press UTIL  Record  Mode and use

RIGOL DS6000 User’s Guide 10-7 3. Start Press the Satrt softkey or press the Run/Stop key to enable waveform analysis. Note that during

RIGOL DS6000 User’s Guide 10-8 5. Previous After the waveform analysis finishes, press the Previous softkey can locate the error frame befo

RIGOL DS6000 User’s Guide 10-9 Analysis Based on Trace Press the Analyze softkey and select “Trace”. Then, set the templet used in analysis based o

RIGOL DS6000 User’s Guide 10-10 Analysis Based on Pass/Fail Mask Press the Analyze softkey and select “Pass/Fail”. Then, set the

RIGOL DS6000 User’s Guide 11-1 11 Display Control You can set the type, the persistence time and the brightness of waveform display as well as th

RIGOL DS6000 User’s Guide 11-2 To Select the Display Type Press DISP  Type to set the waveform display mode to “Vectors” or “Dots”. 

RIGOL DS6000 User’s Guide 11-3 To Set the Persistence Time Press DISP  Persis. Time to set the persistence time of the oscilloscope to Vmin, specifi

RIGOL DS6000 User’s Guide XVII Acquisition Mode ... 4-2 Normal ...

RIGOL DS6000 User’s Guide 11-4 3. Infinite In this mode, the oscilloscope displays the waveform newly acquired without clearing the wave

RIGOL DS6000 User’s Guide 11-5 To set the Waveform Brightness Press DISP  WaveIntensity or turn in normal operation mode to adjust the waveform

RIGOL DS6000 User’s Guide 12-1 12 Store and Recall Users can save the current settings, waveforms, and screen image in internal memory

RIGOL DS6000 User’s Guide 12-2 Storage System Press SAVE to enter the store and recall setting interface. This oscilloscope provides two

RIGOL DS6000 User’s Guide 12-3 Storage Type Press SAVE  Storage to select the desired storage type. The default is “Traces”. The store and recall de

RIGOL DS6000 User’s Guide 12-4 One-key Bitmap Saving After a USB flash device is connected, press the print key at the front panel to

RIGOL DS6000 User’s Guide 12-5 Internal Store and Recall Internal store and recall support “Traces”, “Waveforms” and “Setups” in Storage. In the foll

RIGOL DS6000 User’s Guide 12-6 Figure b Note that in internal storage, New menu is not available. 2. Load the specified type of file in th

RIGOL DS6000 User’s Guide 12-7 Figure d

RIGOL DS6000 User’s Guide XVIII Logic Operation ... 6-8 Advanced O

RIGOL DS6000 User’s Guide 12-8 External Store and Recall Before using external store and recall, make sure that a USB flash devic

RIGOL DS6000 User’s Guide 12-9 Figure f 4) After the storage position is selected, press New to turn on the interface as shown in Figure g. Refer t

RIGOL DS6000 User’s Guide 12-10 Figure h 2) As shown in Figure i, use to select the desired file to load and then press Load to load t

RIGOL DS6000 User’s Guide 12-11 Disk Management Press SAVE  Disk.Manage to turn on the disk management interface as shown in the figure below and us

RIGOL DS6000 User’s Guide 12-12 To Create a New File or Folder This operation is only valid in external storage. Before using external store

RIGOL DS6000 User’s Guide 12-13 English Input Method For example: create a file or folder using the name “Filename”. 1. Press Keyboard. 1) Use

RIGOL DS6000 User’s Guide 12-14 Chinese Input Method For example: create a file or folder using the name “文件名”. 1. Press Keyboard. 1) Use

RIGOL DS6000 User’s Guide 12-15 To Delete a File or Folder Folder operation is valid only in external storage. Before using the external d

RIGOL DS6000 User’s Guide 12-16 To Copy and Paste a File You can copy a file in the local disk to the external disk or copy a file in one ext

RIGOL DS6000 User’s Guide 12-17 Factory Press SAVE  Factory to return the oscilloscope to its factory state. Refer to the table below. Table 12-2 F

RIGOL DS6000 User’s Guide XIX 10 Waveform Recording ... 10-1 Waveform Recording...

RIGOL DS6000 User’s Guide 12-18 Bandwidth OFF Input Impedance 1 MΩ Channel Invert OFF Vertical Scale Coarse Channel Unit V Acquisition Settin

RIGOL DS6000 User’s Guide 12-19 Track Cursor A CH1 Cursor B CH2 CurA -4*1 us CurB 4*1 us Storage Setting (SAVE) Storage Type Traces Utility Function

RIGOL DS6000 User’s Guide 12-20 Power On Recall Last Vertical Expansion Ground Screen Saver Default Screen Saver Time OFF External Trigger Imp

RIGOL DS6000 User’s Guide 12-21 Vertical Scale 10 dB Vrms/div Vertical Scale 1.25 MHz Sample Rate 50 MSa/s Logic Operation Expression AND Source A CH1

RIGOL DS6000 User’s Guide 12-22 Packet End NULL SPI SS Channel OFF SS Polarity Positive SCLK Channel CH2 SCLK Slope Rising Edge MISO Channel C

RIGOL DS6000 User’s Guide 13-1 13 System Function Setting The contents of this chapter:  Remote Interface Configuration  System-related 

RIGOL DS6000 User’s Guide 13-2 Remote Interface Configuration DS6000 can communicate with PC via LAN, USB and GPIB (together with the USB to

RIGOL DS6000 User’s Guide 13-3 IP Configuration Type (DHCP) The configuration type of the IP address can be DHCP, auto IP or static IP.

RIGOL DS6000 User’s Guide 13-4 nnn is from 0 to 223 (except 127) and the ranges of the other three nnn are from 0 to 255. You are recommended

RIGOL DS6000 User’s Guide 13-5 range of the first nnn is from 0 to 223 (except 127) and the ranges of the other three nnn are from 0 to 255. You are r

RIGOL DS6000 User’s Guide XX System Time ... 13-8 Self-calibrati

RIGOL DS6000 User’s Guide 13-6 USB Device This oscilloscope can communicate with a PC or PictBridge printer via the USB Device in

RIGOL DS6000 User’s Guide 13-7 System-related Sound When the sound is enabled, you can hear the sound of the beeper when you press a function key or

RIGOL DS6000 User’s Guide 13-8 Power-off Recall You can set the system configuration to be recalled when the oscilloscope is powered on ag

RIGOL DS6000 User’s Guide 13-9  Year: 2000 to 2099  Month: 01-12  Date: 01-31 (28, 29 or 30)  Hour: 00 to 23  Minute: 00 to 59  Second: 00

RIGOL DS6000 User’s Guide 13-10 Self-calibration Information Press UTIL  System  SelfCalInfo to view the result of the last self-calibratio

RIGOL DS6000 User’s Guide 13-11 Screen When the oscilloscope enters the idle state and holds for a certain period of time, the screen saver program w

RIGOL DS6000 User’s Guide 13-12 Error Information If this menu is shown in gray, it means that the circuit board of the oscilloscope is worki

RIGOL DS6000 User’s Guide 13-13 Self-calibration Self-calibration program can quickly help the oscilloscope to reach the best working state and get t

RIGOL DS6000 User’s Guide 13-14 Power Status Users can set the power status of the oscilloscope after power-on. Connect the oscil

RIGOL DS6000 User’s Guide 13-15 Aux Output Users can set the signal type output from the [Trig Out/Calibration] connector at the rear panel. Press U

RIGOL DS6000 User’s Guide 1-1 1 Quick Start This chapter introduces the preparations when using the oscilloscope for the first time, the front p

RIGOL DS6000 User’s Guide 13-16 Reference Clock This oscilloscope can output the internal 10 MHz sample clock from the [10MHz In/

RIGOL DS6000 User’s Guide 13-17 Option Management This oscilloscope provides multiple options to fulfill your measurement requirements. Please conta

RIGOL DS6000 User’s Guide 13-18 To Print the Waveform To Connect the Print Device DS6000 oscilloscope supports normal and PictBridge printer

RIGOL DS6000 User’s Guide 13-19 Normal Print After “Normal” is selected, please refer to the following steps to set the print parameters

RIGOL DS6000 User’s Guide 13-20 PictBridge Print After selecting the “PictBridge” print mode, please refer to the following steps to set

RIGOL DS6000 User’s Guide 13-21 function. 7. Quality Press this softkey to select the print quality. You can select: Default, Normal, Draft or Fine.

RIGOL DS6000 User’s Guide 14-1 14 Remote Control The oscilloscope can be controlled remotely mainly using the following two methods: User-define

RIGOL DS6000 User’s Guide 14-2 Remote Control via USB 1. Connect the device Connect the oscilloscope (USB DEVICE) with your PC using a USB c

RIGOL DS6000 User’s Guide 14-3 7 5 6

RIGOL DS6000 User’s Guide 1-2 General Inspection 1. Inspect the shipping container for damage. If your shipping container appears to be dama

RIGOL DS6000 User’s Guide 14-4 3. Search device resource Start up the Ultra Sigma and the software will automatically search for the oscillos

RIGOL DS6000 User’s Guide 14-5

RIGOL DS6000 User’s Guide 14-6 Remote Control via LAN 1. Connect the device Connect the oscilloscope to your LAN using a network cable. 2.

RIGOL DS6000 User’s Guide 14-7 5. Communication test Right click the resource name “DS6104 (TCPIP::172.16.3.88::INSTR)” to select “SCPI Panel Contr

RIGOL DS6000 User’s Guide 14-8

RIGOL DS6000 User’s Guide 14-9 Remote Control via GPIB 1. Connect the device Use the USB to GPIB module to extend a GPIB interface for the oscillosc

RIGOL DS6000 User’s Guide 14-10 5. View device resource Click “OK” to return back to the main interface of Ultra Sigma. The resources found w

RIGOL DS6000 User’s Guide 15-1 15 Troubleshooting The commonly encountered failures and their solutions are listed below. When you encounter thos

RIGOL DS6000 User’s Guide 15-2 (2) Check the trigger type: general signals should use “Edge” trigger and video signal should use “Video” trig

RIGOL DS6000 User’s Guide 16-1 16 Specifications All the specifications are guaranteed except the parameters marked with “Typical” and the oscill

RIGOL DS6000 User’s Guide 1-3 Appearance and Dimensions Figure 1-1 Front View Unit: mm Figure 1-2 S

RIGOL DS6000 User’s Guide 16-2 Probe Attenuation Coefficient 0.001X, 0.01X, 0.1X, 1X, 10X, 100X, 1000X Maximum Input Voltage (1MΩ) Maximum I

RIGOL DS6000 User’s Guide 16-3 230 mV/div to 5 V/div: ± 40V (1MΩ) Bandwidth Limit2 20 MHz or 250 MHz Low Frequency Response (AC Coupling -3dB) ≤5 Hz (

RIGOL DS6000 User’s Guide 16-4 Negative Slope (greater than, lower than, within specific interval) Time Setting 10 ns to 1 s Video Trigger Sig

RIGOL DS6000 User’s Guide 16-5 Trigger condition SOP, EOP, RC, Suspended, Exit Suspended Measure Cursor Manual Mode Voltage Deviation between Curso

RIGOL DS6000 User’s Guide 16-6 FFT Vertical Scale Linear RMS, dBV RMS Logic Operation AND, OR, NOT, XOR Math Function Intg, Diff, Log, Exp, Sq

RIGOL DS6000 User’s Guide 16-7 Power Power Voltage 100-120 V/50Hz/60Hz/400Hz 100-240 V/50 Hz/60Hz Power Maximum 150W Fuse 3 A, T Degree, 250 V Environ

RIGOL DS6000 User’s Guide 17-1 17 Appendix Appendix A: Options and Accessories Description Order Number Model DS6104 (1 GHz, 4-channel) DS6104 D

RIGOL DS6000 User’s Guide 17-2 Appendix B: Warranty RIGOL warrants that its products mainframe and accessories will be free from defects in m

RIGOL DS6000 User’s Guide 17-3 Appendix C: Any Comment or Question? If you have any comment or question on our document, please send email to: servic

RIGOL DS6000 User’s Guide 1-4 To Prepare the Oscilloscope for Use To Remove the Cover Before using the oscilloscope, remove the front

RIGOL DS6000 User’s Guide 1 Index Acquisition Mode ... 4-2 Addition ... 6-2 AND ...

RIGOL DS6000 User’s Guide 2 Track Mode ... 6-31 Trigger Coupling ... 5-5 Trigger Holdoff ...

RIGOL DS6000 User’s Guide 1-5 To Adjust the Supporting Legs Adjust the supporting legs properly to use them as stands to tilt the oscilloscope upw

RIGOL DS6000 User’s Guide 1-6 To Connect to AC Power Supply This oscilloscope accepts two kinds of AC power supply: 100-127V, 4

RIGOL DS6000 User’s Guide 1-7 To Use the Battery This oscilloscope also provides rechargeable battery on your option. Please install the battery as s

RIGOL DS6000 User’s Guide I Guaranty and Declaration Copyright © 2010 RIGOL Technologies, Inc. All Rights Reserved. Trademark Information RIGOL i

RIGOL DS6000 User’s Guide 1-8 Power-on Inspection When the oscilloscope is energized, press the power key at the lower-left corner of the

RIGOL DS6000 User’s Guide 1-9 To Connect the Probe RIGOL provides passive and active probes for the DS6000 series oscilloscopes. For detailed technic

RIGOL DS6000 User’s Guide 1-10 Function Inspection 1. Press SAVE  Factory to restore the oscilloscope to its default configuration. 2. Use

RIGOL DS6000 User’s Guide 1-11 WARNING To avoid electric shock during the use of probe, please make sure that the insulated wire of the probe

RIGOL DS6000 User’s Guide 1-12 Probe Compensation When the probes are used for the first time, you should compensate the probes to match the

RIGOL DS6000 User’s Guide 1-13 Front Panel Overview Figure 1-11 Front Panel Overview Table 1-1 Front Panel Description No. Description No. Descri

RIGOL DS6000 User’s Guide 1-14 Rear Panel Overview Figure 1-12 Rear Panel Overview 1. Trig Out/Calibration This connector can outpu

RIGOL DS6000 User’s Guide 1-15 2. Reference Clock Provide more precise sample clock signal for the oscilloscope and it can also synchroni

RIGOL DS6000 User’s Guide 1-16 Front Panel Function Overview VERTICAL CH1, CH2, CH3, CH4: analog input channels. The four channels are

RIGOL DS6000 User’s Guide 1-17 position quickly. VERTICAL SCALE: modify the vertical scale of the current channel. Turn clockwise to decr

RIGOL DS6000 User’s Guide II Safety Requirement General Safety Summary Please review the following safety precautions carefully before putti

RIGOL DS6000 User’s Guide 1-18 HORIZONTAL MENU: press this key to turn on the horizontal control menu under which to turn on or off

RIGOL DS6000 User’s Guide 1-19 TRIGGER MODE: press this key to switch the trigger mode to Auto, Normal or Single and the corresponding state backlig

RIGOL DS6000 User’s Guide 1-20 Single Press this key to set the trigger mode to “Single”. In single trigger mode, press the FORCE

RIGOL DS6000 User’s Guide 1-21 Navigation Knob This knob provides quick Adjust/Locate function for numerical parameters with relatively large settabl

RIGOL DS6000 User’s Guide 1-22 refer to the introduction in “To Use the Built-in Help System”. Record Play/Pause: press this key to play the

RIGOL DS6000 User’s Guide 1-23 User Interface DS6000 oscilloscope provides 10.1 inches, WVGA (800*480) 160,000 color TFT LCD. What is worth menti

RIGOL DS6000 User’s Guide 1-24 1. Measurement Menu Provide 12 horizontal (HORIZONTAL) and 10 vertical (VERTICAL) measurement paramet

RIGOL DS6000 User’s Guide 1-25 9. Trigger Type Display the currently selected trigger type and trigger condition setting. Different labels

RIGOL DS6000 User’s Guide 1-26  Use VIRTICAL SCALE to modify this parameter.  The following labels will be provided according to the cu

RIGOL DS6000 User’s Guide 1-27 Denote that you can use the Navigation Knob to quickly adjust/locate parameters. Denote that can be used to adju

RIGOL DS6000 User’s Guide III Avoid Circuit or Wire Exposure. Do not touch exposed junctions and components when the unit is powered. Do Not Operate

RIGOL DS6000 User’s Guide 1-28 To Use the Security Lock If needed, you can use the security lock (please buy it yourself) to loc

RIGOL DS6000 User’s Guide 1-29 To Use the Desk Mount Instrument Arm Using an arm, the oscilloscope could be mounted on the work desk to save your o

RIGOL DS6000 User’s Guide 1-30 To Use the Rack Mount Kit This oscilloscope can be mounted in a standard 19-inch rack cabinet that conforms to

RIGOL DS6000 User’s Guide 1-31 2-1 2-2 2-3 Installation Tool PH2 Phillips Screw

RIGOL DS6000 User’s Guide 1-32 Installation Space The following requirements must be fulfilled by the machine cabinet in which the instrumen

RIGOL DS6000 User’s Guide 1-33 Installation Procedures Only authorized operators can execute the installation operation. Improper installatio

RIGOL DS6000 User’s Guide 1-34 3. Fix the instrument: fix the instrument on the support board with two back battens and twelve M4

RIGOL DS6000 User’s Guide 1-35 5. Load into the machine cabinet: mount the rack with the instrument fixed to it into a standard 19-inch machine cabin

RIGOL DS6000 User’s Guide 1-36 To Use the Built-in Help System The help system of this oscilloscope provides instructions for all the functio

RIGOL DS6000 User’s Guide 2-1 2 To Set the Vertical System The contents of this chapter:  To Enable the Channel  Channel Coupling  Bandw

RIGOL DS6000 User’s Guide IV Safety Terms and Symbols Terms in this Manual. The following terms may appear in this manual: WARNING Warn

RIGOL DS6000 User’s Guide 2-2 To Enable the Channel DS6000 provides four analog input channels (CH1-CH4) and each channel can be controlled i

RIGOL DS6000 User’s Guide 2-3 Channel Coupling Set the coupling mode to filter out the signals that is not needed. For example: the signal under test

RIGOL DS6000 User’s Guide 2-4 Bandwidth Limit Set the bandwidth to reduce display noise. For example: the signal under test is a pulse signal

RIGOL DS6000 User’s Guide 2-5 Table 2-1 Probe Attenuation Coefficient Menu Attenuation coefficient 0.001X 0.01X 0.1X 1X 10X 100X 1000X 1:1000 1:100 1:

RIGOL DS6000 User’s Guide 2-6 Input Impedance To reduce the circuit load caused by the interaction of the oscilloscope and the circuit under

RIGOL DS6000 User’s Guide 2-7 Waveform Invert When waveform invert is turned on, the waveform display rotates 180 degree relative to the

RIGOL DS6000 User’s Guide 2-8 Vertical Expansion When using VERTICAL SCALE to change the vertical scale of the analog channel, y

RIGOL DS6000 User’s Guide 2-9 Channel Label You can modify the labels used to mark the analog channels (CH1 to CH4) at the left side of the screen. T

RIGOL DS6000 User’s Guide 3-1 3 To Set the Horizontal System The contents of this chapter:  Delayed Sweep  Time Base Mode  Horizontal Scal

RIGOL DS6000 User’s Guide V Measurement Category Measurement Category DS6000 series digital oscilloscopes can make measurements in Measureme

RIGOL DS6000 User’s Guide 3-2 Delayed Sweep Delayed sweep can be used to enlarge a length of waveform horizontally to view the details of the

RIGOL DS6000 User’s Guide 3-3 The waveform before enlargement: The waveform in the area that has not been covered by the subtransparent blue

RIGOL DS6000 User’s Guide 3-4 Time Base Mode Press the MENU key in the horizontal control area at the front panel and then press the Time Bas

RIGOL DS6000 User’s Guide 3-5 X-Y Mode In this mode, the oscilloscope automatically turns on all the four channels (CH1-CH4) and the screen is di

RIGOL DS6000 User’s Guide 3-6 X-Y function can be used to measure the phase deviation occurred when the test signal passes through a circuit n

RIGOL DS6000 User’s Guide 3-7  When X-Y mode is turned on, “Delayed” will be turned off automatically.  The following functions are not available

RIGOL DS6000 User’s Guide 3-8 Roll Mode In this mode, the waveform scrolls from the right to the left to update the display and the waveform

RIGOL DS6000 User’s Guide 3-9 Horizontal Scale Being similar to “Vertical Scale”, the horizontal scale adjustment has two modes : “Coarse” and “Fine

RIGOL DS6000 User’s Guide 3-10 Horizontal Reference Horizontal reference is the reference position according to which the screen wa

RIGOL DS6000 User’s Guide 3-11 direction, the screen can display a maximum of 700 points with the leftmost as 350 and the rightmost as -350. For examp

RIGOL DS6000 User’s Guide VI Ventilation Requirement This oscilloscope uses fan to force cooling. Please make sure that the air intake and ex

RIGOL DS6000 User’s Guide 4-1 4 To Set the Sample System The contents of this chapter:  Acquisition Mode  Sample Mode  Sample Rate  Me

RIGOL DS6000 User’s Guide 4-2 Acquisition Mode The acquisition mode is used to control how to generate waveform points from the sample points

RIGOL DS6000 User’s Guide 4-3 The available range of the number of averages is from 2 to 8192 and the default is 2. When “Average” mode is selected, p

RIGOL DS6000 User’s Guide 4-4 Peak Detect In this mode, the oscilloscope acquires the maximum and minimum values of the sample interval signa

RIGOL DS6000 User’s Guide 4-5 Sample Mode Press ACQ  Sampling and press this softkey continuously to switch the sample mode (the default is real

RIGOL DS6000 User’s Guide 4-6 Sample Rate Sample rate refers to the process that the oscilloscope converts the analog signals to discrete dat

RIGOL DS6000 User’s Guide 4-7 3. Waveform Leakage: when the sample rate is too low, the waveform rebuilt by the sample data does not reflect all t

RIGOL DS6000 User’s Guide 4-8 Memory Depth Memory depth refers to the number of waveform points that the oscilloscope can store in a single t

RIGOL DS6000 User’s Guide 4-9 Antialiasing At slower sweep speeds, the sample rate is reduced and a proprietary display algorithm is us

RIGOL DS6000 User’s Guide VII Working Environment Temperature Operating: 0℃ to +50℃ Non-operating: -20℃ to +70℃ Humidity Under +35℃: ≤90％ relative

RIGOL DS6000 User’s Guide 5-1 5 To Trigger the Oscilloscope When working, the oscilloscope continuously acquires waveform data even if a valid tr

RIGOL DS6000 User’s Guide 5-2 Trigger Source Press MENU  Source in the trigger control area (TRIGGER) at the front panel to select the desir

RIGOL DS6000 User’s Guide 5-3 Trigger Mode Trigger mode would influence the mode in which the oscilloscope searches for trigger event. The following

RIGOL DS6000 User’s Guide 5-4 Auto: No matter whether the trigger condition is met, there is always waveform display. A horizontal line is dis

RIGOL DS6000 User’s Guide 5-5 Trigger Coupling Trigger coupling decides which kind of components will be transmitted to the trigger circuit. Note to

RIGOL DS6000 User’s Guide 5-6 Trigger Holdoff Trigger holdoff could trigger complicated waveforms (e.g. pulse sequence) stably. Holdoff ti

RIGOL DS6000 User’s Guide 5-7 Noise Rejection Noise Rejection reduces noise on the diplayed waveform and stablizes the displayed waveform. Press MEN

RIGOL DS6000 User’s Guide 5-8 Trigger Type DS6000 has abundant trigger functions including multiple serial bus triggers.  Edge Trigger 

RIGOL DS6000 User’s Guide 5-9 Edge Trigger Trigger on the trigger threshold of the specified edge of the input signal. Trigger Type: Press Type to s